Diseño de conveyor - Conveyor design

Ολοκληρωμένο Αναρτήθηκε Πριν 7 χρόνια Πληρώθηκε κατά την παράδοση
Ολοκληρωμένο Πληρώθηκε κατά την παράδοση

Se require un conveyor para el automatizar una seccion del proceso de Dy-check los datos del motor son de uno existente de jaula de ardilla de velocidad 1800 rpm y potencia de 13 kW. Este motor debera mover al conveyor a una velocidad 240 rpm; se recomienda poner las poleas en el motor y las estrellas en la máquina, quedando los engranajes en el medio. por lo que necesita un sistema de transmicion (requisicion de cliente)

1. Determinación de los principales parámetros de las tres transmisiones

2. Cálculo de las fuerzas y selección de los rodamientos: El esquema es de dos flechas intermedias que soportaran una: la polea de salida y el piñón de entrada y la otra: el engranaje de salida y la catalina de entrada, ya que la polea de entrada es soportada por la flecha del motor y la catalina de salida por la de la máquina.

Los cálculos de estas fuerzas permitirán calcular y seleccionar los rodamientos, que soportarán a dichas flechas. Las transmisiones deben ser lo más compacta posibles; la elaboración de un esquema general de la instalación es imprescindible y fundamental ya que este es para una empresa y requieren de dichos esquemas en caso de desmontar, daño de alguna pieza sean capaces de reempazarla.

3. Diseño de las flechas intermedias: tener en cuenta los parámetros de los engranajes, cojinetes, poleas, estrellas y sus chavetas, ya que esos elementos van montados en las flechas. Adicionalmente, tienen que definir los ajustes y tolerancias de las uniones, así como los acabados superficiales.

4. Planos: de cada parte importante y el montado.

Basicamente se require este nivel de detalle ya que algunas piezas las pueden fabricar el personal de mantenimiento y otras se obtendran aparte por lo que se require un nivel bajo de error.

Adjunto vienen algunos calculos y bocetos pueden hacer el proyecto sin seguir estos datos ya que solo son una referencia

A conveyor is required to automate a section of the Dy-check process. The engine data is from an existing squirrel cage of speed 1800 rpm and power of 13 kW. This engine must move the conveyor at a speed of 240 rpm; It is recommended to put the pulleys in the engine and the stars in the machine, leaving the gears in the middle. So it needs a transmission system (customer requisition)

1. Determination of the main parameters of the three transmissions

2. Calculation of the forces and selection of the bearings: The diagram is of two intermediate arrows that would support one: the output pulley and the input pinion and the other: the output gear and the catalina of input, since the pulley Input is supported by the motor shaft and the output shaft by the machine.

The calculations of these forces will allow calculating and selecting the bearings, which will support these arrows. The transmissions should be as compact as possible; The elaboration of a general scheme of the installation is essential and fundamental since it is for a company and they require of said schemes in case of disassembling, damage of some part they are able to repower it.

3. Design of the intermediate arrows: take into account the parameters of the gears, bearings, pulleys, stars and their keys, since these elements are mounted on the arrows. In addition, they have to define the adjustments and tolerances of the joints, as well as the surface finishes.

4. Plans: of each important part and the assembled.

Basically this level of detail is required since some parts can be manufactured by the maintenance personnel and others will be obtained separately, thus requiring a low level of error.

Attached are some calculations and sketches can do the project without following these data as they are only a reference

AutoCAD Μηχανολογία Υλικών Μηχανική Μηχανολογία Mechatronics Μεταφραστής Ισπανικών

Ταυτότητα Εργασίας: #12109610

Σχετικά με την εργασία

8 προτάσεις Απομακρυσμένη εργασία Ενεργό Πριν 7 χρόνια

Ανατέθηκε στον:

panfilinomonaco

Ha trabajado con diseño de Maquinas. Soy profesor Universitario y el diseño mecanico es una de mis area de aplicación

$2000 MXN σε 7 μέρες
(2 Αξιολογήσεις)
2.0

8 freelancers κάνουν προσφορές κατά μέσο όρο $2288 για αυτή τη δουλειά

IngCEA

Buenos días, puedo hacer el primer punto en 5 días, el segundo en 5 días, el tercer punto en 5 días, y los planos los podemos generar en 1 día o como máximo. Ya debes haber visto mi propuestas en tu proyecto anterior, Περισσότερα

$3950 MXN σε 16 μέρες
(20 Αξιολογήσεις)
6.3
asimcosic

A proposal has not yet been provided

$3555 MXN σε 5 μέρες
(26 Αξιολογήσεις)
6.1
prashantdiatm09

Please see my portfolio and reviews once " https://www.freelancer.in/u/prashantdiatm09.html " young energetic and experienced mechancial industrial design engineer. Expert Autocad, Sketchup , and fusion 360 user. Ex Περισσότερα

$3333 MXN σε 12 μέρες
(139 Αξιολογήσεις)
6.0
giritech

Hello, Please allow me to introduce myself. My name is GIRISHA, And I have been a graphic designer for the past 7+ years, Working on staff for commercial agencies serving the GRAPHIC Design and other Designing stu Περισσότερα

$944 MXN σε 1 μέρα
(4 Αξιολογήσεις)
3.1
eskemar

Dear please give me the chance to work for you I am Civil Engineer and I have good computer skill, I have been in designing and drawing in Auto CAD, 2D, 3D modeling for many years. This is my first time on this site a Περισσότερα

$1000 MXN σε 3 μέρες
(8 Αξιολογήσεις)
3.2
DesignEnlight

Dear Employer, I would like to apply as a Designer in your job post. It says that you are looking for Graphic Designer and also who is a detail-oriented person. I think that I am the right person for the job. I Περισσότερα

$525 MXN σε 0 μέρες
(0 Αξιολογήσεις)
0.0